DIY: How to Dropkick a Claymore Mine

Today I have a Do-It-Yourself guide on how to “dropkick” a Claymore Anti-Personnel mine for you guys.  This is a technique I learned in Ranger Battalion and was able to use later on when I was in Special Forces.  The term dropkick is of course just shorthand for a method of rigging the Claymore mine for a very fast employment when outnumbered and outgunned by the enemy.  Also known as the “red vapor mist machine” in some circles, the Claymore mine is typically used to protect soldiers in static positions such as patrol bases, or used to initiate an ambush against enemy troops.  The dropkick technique is different in that it is used by snipers, recce patrols, or other small SOF teams who are breaking contact with the enemy and attempting to escape and evade.

So here it is, the Claymore Mine that we all know and love.  With a layer of plastic explosives lining the inside of the curve shaped mine, there are about 700 ball bearings laid into the explosives that fire forward at enemy troops as shrapnel.  I’m out of the military now so this demonstration was done with an inert trainer rather than the real deal!

Step 1: Take inventory and test equipment.  You will need everything you see above and a knife for this project.  Use the test set to test the Claymore out on the range for functionality.  Go through the entire process, EIB standards and everything.  If you actually have to use a dropkicked Claymore in combat, you need it to work, so don’t cut any corners here.  Check the mine, wire, and clacker for serviceability and scrounge up some rubber bands; you’ll see why in a minute.

Step 2: First we need to prepare the Claymore bag that the mine comes in.  Directions on how to employ the mine are sewn into the cover of the bag.  This is going to get in the way as we move forward, so do yourself a favor and cut or tear these out now.

Make your Claymore bag look like this and we are ready to move on to the next step.

Step 3: The Claymore bag is partitioned down the middle into two pouches, one for the Claymore mine and one for the wire with blasting cap, clacker, and test set.  We need to cut down this partition so that we have one big pouch in the bag.

Once your Claymore bag looks like this you will be ready to go on to the next step.

Step 4: Extend the legs of the Claymore mine and put it in the bag to see where the legs poke into the bottom.

      Use your knife to cut slits in the bottom of the bag and ensure that the legs of the mine can slide through.

Step 5: Back to the lid of the bag.  Cut slits up both sides of the lid, three on each side.  Make sure that they are equally spaced apart and don’t go past the buttons.

Step 6: Take the rubber bands and loop them through the slits that you made in the cover, then loop the bands back on themselves, making a bite around the fabric of the lid.  Do this for each of the six slits that you cut.

Step 6: This is where it gets a little tricky.  Figure out how much length of the Claymore wire covers and surpasses the length of the lid.  In my case, I can wrap the cord around my elbow and over my palm to make a spool, and that fits nicely for our purposes.  This might require some experimentation on your part to get it right.  You will need to make three separate wraps that will be locked into place with the rubber bands, so plan ahead.

Start stringing the Claymore wire back and forth.  Once you get enough wraps, separating the wire equally into thirds, go ahead and lock the ends into the loops of the rubber bands.  You may need to twist the rubber bands and loop them back around the wire a second time to make sure it’s in there nice and snug.

 This is what it should look like when you are done.  During this process it is critical that you are careful with the blasting cap when doing this with a live mine.  When I worked with live demo, I’d keep the cap inside the plastic spool that the wire comes on for safety purposes.

Step 7: Put the Claymore mine back in the bag, push the metal legs through the slits you cut in the bottom, and fold them down and out of the way for transportation.

Step 8: Arm the mine.  Screw the blasting cap into the mine when appropriate.  This depends on unit SOP, so if you Privates out there need to check with your Squad Leader before you Sua Sponte this!  Army regs say that no charges or explosives can be primed with initiation systems until they are going to be used.  Most SOF units these days are priming their charges on the FOB beforehand and rolling out to their targets.  How your unit does is METT-T (situation) dependent.

Here is the finished product, you’ve dropkicked a claymore mine.  The mine can now be carried by the sling or kept on an external pouch on a rucksack.  When a small recce patrol makes contact and can’t wait for air support, it’s time to use this bad boy.  Extend the claymore legs, stick it in the ground (THIS SIDE FACES ENEMY), pull however much wire you need to get you behind cover and concealment, run to cover, pop the shipping plugs, and attach the clacker.  Once a pursuing enemy closes in on your position, you know what to do!

Writing up this DIY guide cost me some money; would you believe that a used Claymore trainer costs almost 200 dollars?!  I think it was worth the trouble, but if you guys learned anything from this post, please help us out and make this DIY guide famous.  Use the like button and share this with as many people as possible.  Thanks guys.



Read more: http://kitup.military.com/2012/01/diy-dropkick-claymore.html#ixzz1izpIEb1x 
Kit Up! 

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s